@article { author = {Ramezani Etedali, Hadi and zarakani, kyvan and fakhar, mohadese sadat}, title = {Determining The Appropriate Values Of Irrigation System Design Parameters Tape And Strip System With Two Continuous Flow Regimes And Decrease Flow}, journal = {Iranian Journal of Irrigation & Drainage}, volume = {15}, number = {1}, pages = {177-187}, year = {2021}, publisher = {Iranian Irrigation and Drainage Association}, issn = {2008-7942}, eissn = {2676-6884}, doi = {}, abstract = {Today, due to high water consumption in the agricultural sector and the water crisis in the country, efforts have been made to improve irrigation methods. Given that agricultural irrigation is still superficial, it is necessary to find a solution to improve these methods at a much lower cost than pressurized irrigation. The purpose of this study is to use SIRMOD software to determine the optimal values of design parameters such as length, flow and cut-off time in two continuous flow regimes and flow reduction in strip and stream irrigation systems. Using the SIRMOD model, 25 and 50% of the actual values of field length, inlet flow and cut-off time were generated. The results showed that with a reduction of 25 to 50% in the length and flow rate to the farm, evaluation indicators such as application efficiency, storage efficiency, distribution uniformity, increase significantly And runoff ratio and deep penetration ratio were significantly reduced. The results of the effect of changes in tape length on evaluation indicators show that the amount of storage efficiency in the range (-0.5 to +0.25) is almost a constant value equal to 100, but in the range (+0.25 to +0.5) The efficiency has changed even in some places to 80, and the application efficiency in most furrows is a value between (90 to 40). The results showed that the flow reduction method, while being effective in increasing the evaluation indicators due to the interruption of water flow by the farmer after the end of the progress phase, especially in strip irrigation, did not have a significant effect on increasing the indicators.}, keywords = {Input flow,Application efficiency,Farm length}, title_fa = {تعیین مقادیر مناسب پارامتر‌های طراحی سیستم آبیاری با دو رژیم جریان پیوسته و کاهش جریان}, abstract_fa = {امروزه با توجه به مصرف بالای آب در بخش کشاورزی و بحران آب در کشور اهتمام به اصلاح روش‌های آبیاری مضاعف گشته است. باتوجه به اینکه بخش زیادی از اراضی آبی هنوز به صورت سطحی می‌باشد، یافتن راه‌حلی به منظور اصلاح روش‌های مذکور با هزینه‌‌هایی به مراتب کمتر از آبیاری تحت فشار ضروری است. هدف از این تحقیق استفاده از نرم افزار SIRMOD برای تعیین مقادیر بهینه پارامتر-های طراحی مانند طول، دبی و زمان قطع جریان در دو رژیم جریان پیوسته و کاهش جریان در سیستم‌های آبیاری نواری و جویچه‌ای است که بدین منظور با استفاده از مدل SIRMOD اقدام به سناریو‌سازی به میزان 25 و 50 درصد مقادیر واقعی طول مزرعه، دبی ورودی و زمان قطع جریان اقدام شد. نتایج نشان داد که با کاهش 25 الی 50 درصدی طول و دبی ورودی به مزرعه، شاخص‌های ارزیابی از قبیل راندمان کاربرد، راندمان ذخیره، یکنواختی توزیع، به صورت چشمگیری افزایش پیدا می‌کند و نسبت رواناب و نسبت نفوذ عمقی کاهش قابل توجهی داشت. نتایج اثر تغییرات طول نوار بر شاخص‌های ارزیابی نشان می‌دهد میزان راندمان ذخیره از بازه (25/0+ تا 5/0-) مقدار تقریبا ثابتی برابر با 100 می‌باشد ولی در بازه‌ی (5/0+ تا 25/0+) میزان راندمان تغییر کرده حتی در بعضی نقاط به مقدار 80 نیز رسیده، و مقدار راندمان کاربرد نیز در اکثر جویچه‌ها مقداری بین (90 تا 40 درصد) می‌باشد. نتایج بیانگر این بود که روش کاهش جریان در عین موثر بودن بر افزایش شاخص‌های ارزیابی با توجه به قطع جریان آب توسط زارع پس از اتمام فاز پیشروی به خصوص در آبیاری نواری تاثیر چشمگیری در افزایش شاخص‌ها نداشت.}, keywords_fa = {دبی ورودی,راندمان کاربرد,طول مزرعه}, url = {https://idj.iaid.ir/article_126751.html}, eprint = {https://idj.iaid.ir/article_126751_c858cf567d7f4236c9d8be729eb9413d.pdf} }