@article { author = {ziaeifar, samira and Meftahhalaghi, Mehdi and Masoudian, Mohsen and Dehghani, Amir Ahmad}, title = {Hydraulic analysis of inclination of half-cylindrical weir-gate with fixed opening}, journal = {Iranian Journal of Irrigation & Drainage}, volume = {12}, number = {3}, pages = {709-721}, year = {2018}, publisher = {Iranian Irrigation and Drainage Association}, issn = {2008-7942}, eissn = {2676-6884}, doi = {}, abstract = {Flow control and measurement structures such as gates and weirs are important components in irrigation and drainage networks. With regard to the problem of sedimentation in weirs and the accumulation of floating materials behind the gates, a combined weir- gate structure to facilitate draining of materials through the gate and suspended materials through weir. One of its types is half-cylindrical weir–gate which, due to the curvature of the flow lines and adhesion on body of the structure, it has advantages including ease of passage of floating objects, ease of design, higher flow discharge coefficient compared with other combined structures (sharp-crested and broad-crested, etc.). This research was aimed to analyze the hydraulic of passing flow from half-cylindrical weir–gate structure by rotating around the center and edges half-cylindrical from 0° to 180° with fixed gate opening height. Experiments were done in a rectangular and horizontal flume with 11 meter length and 30cm width under three models of half-cylindrical weir–gate with 70, 120 and 160 mm diameters. The minimum discharge coefficient occurred at 90° and its maximum happened at 45° and 30° angles, respectively. For diameters of 70, 120 and 160 mm, the minimum back water was observed at 0°, 45° and 30°, respectively, and the largest one was observed at 90° for all three diameters. Moreover, in relation to the depth of upstream water to the opening of the fixed valve, for the angles, by increasing diameter, the discharge coefficient of the combined structure decreased. The results showed that, in addition to the angle of the half-cylindrical curvature relative to horizon line, the diameter of the structure is effective on the discharge coefficient and back water of the combined structure.}, keywords = {Back water,Combined structure,Discharge coefficient,Rotation axis}, title_fa = {تحلیل هیدرولیکی چرخش سرریز- دریچه نیم‌استوانه‌ای با بازشدگی ثابت}, abstract_fa = {سازه‌های کنترل و اندازه‌گیری جریان نظیر دریچه‌ها و سرریزها از اجزای مهم در شبکه‌های آبیاری و زهکشی می‌باشند. با توجه به مشکل رسـوب‌گذاری در سرریزها و تجـمع مواد شـناور پشت دریچه‌ها، مدل سازه ترکـیبی سـرریز- دریچه پیشنهاد گردید تا مواد قابل ته‌نشین به راحتی از دریچه خارج و مواد معلق به شکل بهتری از روی سرریز تخلیه ‌شوند. یکی از انواع آن، سرریز- دریچه نیم‌استوانه‌ای است که به علت انحنای خطوط جریان و چسبیدن جریان به بدنه‌ی سازه دارای مزایایی از جمله سهولت عبور اجسام شناور، سهولت طراحی، ضریب دبی عبوری بالا نسبت به سایر سازه‌های ترکیبی (لبه‌تیز و لبه پهن و ...) می‌باشد. در این پژوهش، هیدرولیک جریان عبوری از مدل فیزیکی سرریز- دریچه نیم‌استوانه‌ای با چرخش حول مرکز و لبه‌ نیم‌استوانه از صفر تا 180 درجه با ارتفاع بازشدگی دریچه ثابت، بررسی شد. آزمایش‌ها در کانالی مستطیلی و افقی به ‌طول 11 متر و عرض 30 سانتی‌متر، تحت سه مدل سرریز- دریچه نیم‌استوانه‌ای با قطرهای 70، 120 و160 میلی‌متر انجام شد. کم‌ترین ضریب دبی در زاویه90 درجه و بیش‌ترین آن به ترتیب در زوایای 45 و30 درجه اتفاق افتاد. برای قطرهای 70، 120 و 160 میلی‌متر، کم‌ترین پس‌زدگی آب به‌ترتیب در زاویه‌ی صفر، 45 و 30 درجه مشاهده شد و بیش‌ترین آن برای هر سه قطر، در90 درجه حاصل گردید. همچنین، در نسبت عمق آب بالادست به میزان بازشدگی دریچه‌ی ثابت، برای زوایای مورد بررسی، با افزایش قطر، ضریب دبی سازه ترکیبی کاهش یافت. نتایج نشان داد که علاوه ‌بر زاویه‌ی قرارگیری انحنای نیم‌استوانه نسبت‌به افق، قطر سازه بر ضریب دبی و پس‌زدگی سازه ‌ترکیبی مؤثر می‌باشد.}, keywords_fa = {پس‌زدگی آب,سازه ترکیبی,ضریب دبی,محور چرخش}, url = {https://idj.iaid.ir/article_73678.html}, eprint = {https://idj.iaid.ir/article_73678_aee69829f98e523f67b31d27e0485a26.pdf} }